Brass Style Pumps

Pump Stack Assemblies:

Includes top and bottom plate, stanchions, and fittings

9713 Pump Brass 1 Stack Complete Assembly
9714 Pump Brass 2 Stack Complete Assembly
9715 Pump Brass 3 Stack Complete Assembly
9716 Pump Brass 4 Stack Complete Assembly
9717 Pump Brass 5 Stack Complete Assembly
9718 Pump Brass 6 Stack Complete Assembly
9724 Pump Brass 7 Stack Complete Assembly
9725 Pump Brass 8 Stack Complete Assembly
Pump Repair Kit for Brass Style Pumps, Air Side
Part Number: 9721
This rebuild kit contains the parts typically needed to get the air side of the pump working again.  (Note the number one cause of failure of this side of the pump is oily air supply.  If you have oil in your air supply then we recommend a coalescing air filter on the supply air)
Pump Repair Kit for Brass Style Pumps, Liquid Side
Part Number: 9199
If your pump is leaking oil, this set of o-rings and urethane check seal, can be replaced and will usually stop the leaking. 
Brass Pump Mounting Kit,
Part Number: 9320

(with 2 screws,2 washers, 2 gaskets, 2 hex sockets (not in photo))
Hex Socket
Part Number: 9287
Used as a plug to close the ports.
Brass Injector Pump,
Part Number: 9300
(Includes: Pump 2 stanchions, 2 pump gaskets)
Pump Kit with no elbow for special connections.
Brass Injector Pump Kit,
Part Number: 9301
(Includes: Pump with elbow, 2 stanchions, 2 pump gaskets)
Add a pump or have a simple replacement solution on hand ready to install in a hurry with minimal down time.
Brass Injector Pump Kit for Individual Controls,
Part Number: 9719
If your applicator has individual controls then you need the modified brass pump with the separate air feed.
Part Number: 9303
Pump Gasket Seal, Standard Buna
Part Number: 9304
Elbow 5/32” X 1/4”NPT bottom of pump stack
Part Number: 9337
Elbow 1/8” X 1/8”NPT end of pump
Part Number: 9334
Assembly for oil hose to box for brass pumps
Part Number: 9702
Compression Nut
Part Number: 9254
Compression nut to hold and seal oil tube 1/8"
Miscellaneous Parts for the Brass Pumps

Keep it simple and stick with the kits and common parts listed above and you should be able to fix any problem you have with your brass pump.  But there are some situations when you only need a certain part.  We don't have them all but we do have some less common parts listed below.  All these parts are subject to minimum orders and availability and may be discontinued at anytime without notice.

Solid Gasket for Independent Control Brass Pump
Part Number: 9308
Use to isolate the independent control pump from the main air port.

Viton is more resistant to mineral oil and solvent than standard rubber and buna seal.  Our brass style pumps use buna seals for the most part, you can order the pumps with viton seals on the oil side which make them more durable when you use mineral oil.  If you are using Accu-Lube natural based oil the buna seals are actually better.  Viton seal versions of the brass pumps and viton seals are all considered special order and some have minimum order quantities and are not returnable.  

  Gasket Seal between Pumps (VITON)
Part Number: 9304V
Viton Gasket for between pump (Special Order Minimum 50 PCS)
  O-Ring for Brass Pump Piston (VITON)
Part Number: 9309V
Seals around the piston (Special Order Minimum 50 PCS)
  Check Seal (VITON)
Part Number: 9316V
Check Seal (Special Order Minimum 50 PCS)